U-Bootに入れたのでデフォルトの設定を載せておく

結局JTAGを注文しました、送料の無駄ですね、、


カーネルの Device Drivers -> USB support -> USB Serial Converter support -> USB FTDI Single Port Serial Driver を有効にしておく

# screen /dev/ttyUSB0 115200

U-Boot 2011.06-02334-g8f495d9-dirty (May 31 2011 - 02:06:26)
Marvell-DreamPlug

SoC:   Kirkwood 88F6281_A0
CPU running @ 1200Mhz L2 running @ 400Mhz
SysClock = 400Mhz , TClock = 200Mhz
DRAM:  512 MiB
SF: Detected MX25L1606 with page size 256, total 1 MiB
In:    serial
Out:   serial
Err:   serial
Net:   egiga0, egiga1
88E1116 Initialized on egiga0
88E1116 Initialized on egiga1
Hit any key to stop autoboot:  0
Marvell>>

Marvell>> printenv
bootcmd=setenv ethact egiga0; ${x_bootcmd_ethernet}; setenv ethact egiga1; ${x_bootcmd_ethernet}; ${x_bootcmd_usb}; ${x_bootcmd_kernel}; setenv bootargs ${x_bootargs} ${x_bootargs_root}; bootm 0x6400000;
bootdelay=3
baudrate=115200
x_bootcmd_ethernet=ping 192.168.2.1
x_bootcmd_usb=usb start
x_bootcmd_kernel=fatload usb 0 0x6400000 uImage
x_bootargs=console=ttyS0,115200
x_bootargs_root=root=/dev/sda2 rootdelay=10
ethact=egiga0
ethaddr=xx:xx:xx:xx:xx:xx
eth1addr=xx:xx:xx:xx:xx:xx
stdin=serial
stdout=serial
stderr=serial

Environment size: 524/4092 bytes

Marvell>> help
?       - alias for 'help'
base    - print or set address offset
bdinfo  - print Board Info structure
boot    - boot default, i.e., run 'bootcmd'
bootd   - boot default, i.e., run 'bootcmd'
bootm   - boot application image from memory
bootp   - boot image via network using BOOTP/TFTP protocol
cmp     - memory compare
coninfo - print console devices and information
cp      - memory copy
crc32   - checksum calculation
date    - get/set/reset date & time
dhcp    - boot image via network using DHCP/TFTP protocol
echo    - echo args to console
editenv - edit environment variable
fatinfo - print information about filesystem
fatload - load binary file from a dos filesystem
fatls   - list files in a directory (default /)
go      - start application at address 'addr'
help    - print command description/usage
iminfo  - print header information for application image
imxtract- extract a part of a multi-image
itest   - return true/false on integer compare
loadb   - load binary file over serial line (kermit mode)
loads   - load S-Record file over serial line
loady   - load binary file over serial line (ymodem mode)
loop    - infinite loop on address range
md      - memory display
mii     - MII utility commands
mm      - memory modify (auto-incrementing address)
mtest   - simple RAM read/write test
mw      - memory write (fill)
nfs     - boot image via network using NFS protocol
nm      - memory modify (constant address)
ping    - send ICMP ECHO_REQUEST to network host
printenv- print environment variables
rarpboot- boot image via network using RARP/TFTP protocol
reset   - Perform RESET of the CPU
run     - run commands in an environment variable
saveenv - save environment variables to persistent storage
setenv  - set environment variables
sf      - SPI flash sub-system
sleep   - delay execution for some time
source  - run script from memory
tftpboot- boot image via network using TFTP protocol
usb     - USB sub-system
usbboot - boot from USB device
version - print monitor version